Architect Spec for: TopCoat Paints

Description:

TopCoat PolyFloor Paint is a carefully balanced formulation of an acrylic emulsion vehicle and selected pigments to form a unique coating system.

Uses:

TopCoat PolyFloor Paint is an integrated color coating system for use on above grade exterior and interior surfaces. It is typically utilized as a coating for "Unity" Surfacing Systems rubberized safety surfacing, flooring and paver products in the tile-mat-block form.

Advantages:

Economical, Weather Resistant, Excellent Adhesion, Strength and Permanence, Safety.

Physical Properties:

Type = Acrylic Emulsion Coating.

Weight per Gallon = 10 lbs per gallon.

Flash Point = None - non flammable

Effect of Freezing = 5 freeze-thaw cycles - Satisfactory

Effect of Heat = 300 hours at 140F - Satisfactory

Surface Preparation:

At time of application, surface temperature must not be below 40F.

Surfaces = All surfaces must be clean, free from dirt, oil, grease, foreign matter and other surface contaminations. New concrete and masonry mortar must be etched with 10% solution of muriatic acid and then thoroughly flushed with cold water.

Variations in surface levels shall not exceed plus or minum3 degrees.

Any required leveling shall be done by the general contractor who shall remove high spots and fill low spots.

Prior Coatings:

Must be firmly bonded and in good condition. If there are any scaling, flaking, peeling or chipping, then the areas in doubt shall be wire brushed or scraped until all poorly bonded materials is removed. Pressure washing or sandblasting is suggested for extensive areas where previous coatings must be removed. Check with "Unity" Surfacing Systems directly or its sales reps for more details information or questions prior to application.

Application:

TopCoat PolyFloor Paint is a base coat - Stir until uniform viscosity is obtained.

Pour on area and spread uniformly with a squeegee, paintbrush, roller or sprayer. Apply at a rate of 100 sq. ft. per gallon on wide strips.

If a second coat is required for additional filling and to uniform the surface, apply at a rate of 100 sq. ft. per gallon at a right angle of the method of applying the first coat. With a sprayer or a wide hair type push broom or lambs wool roller apply at a rate of 200 sq. ft. per gallon to a uniform finish.

Brush apply with a nylon or fiber bristle brush working the material into voids, cracks and crevices to completely seal the surface properly. Finish off with a straight horizontal stroke, using the tip of the brush.

Roller apply the area after brushing for a more uniform finish. It is applied with a long nap masonry roller. Be sure to smooth off any lap marks. The use of a piece of expanded metal cut to fit into a 5 gallon pail and extending about ½ feet out of the paid, will make it easier to take excess paint off the roller and allow it to drain back into the 5 gallon pail.

Coverage:

Filler coat = approximately 100 sq. ft. per gallon

Top coat = approximately 200 sq. ft. per gallon

Line coat = approximately 300 sq. ft. per gallon (depending on the pin striping)

Packaging:

One-gallon containers

Five-gallon containers

55-gallon drums

Touts = 5 - 55 gallon drums

Color:

Terra Cotta (red), Green, Blue, White, Brown, Plum, Sunburst, Teal, Gold (Brown), Bright Red and Yellow.

Caution:

Never store container for more the one year. Never apply below a temperature of 40F. Allow one hour between coats. Do not use for below grade waterproofing.

A complete MSDS of specifications is available by calling: "Unity" Surfacing Systems at (1-877) 41-UNITY or by fax at: (516) 933-3239 or simply e-mail us your request at: Techsupport@surfacingsystems.com The following is made in lieu of all warranties, guarantees, expressed or implied. "Unity" Surfacing Systems only obligation shall be to replace such quantity of the product proved to be defective. Neither seller nor manufacturer shall be liable for any inquiry, loss or damage, direct or consequently arising out of the use of or the inability to use the product. Before using, user shall determine the suitability of the product for his or her intended use, and user assumes all risk and liability whatsoever in connection therewith. The forgoing may not be altered except by an agreement signed by the officer(s) of seller and manufacturer.